Guide

Double wick candles: when you need two wicks and how to space them

Last reviewed November 2026

Jars wider than about 3½ inches are hard to wick with one wick, and CandleScience suggests trying two once a container reaches about 4 inches across. Don't use two wicks sized for the whole jar. Divide the diameter by the number of wicks and size each wick for its own section: a 4 inch jar with two wicks takes two wicks rated for 2 inches. Place each wick about halfway between the centre and the edge, so in a 4 inch jar they sit about 2 inches apart and 1 inch from the glass. Then burn test, because two flames make the jar much hotter than one.

When does a candle need two wicks?

  • Wide jars. Northwood says jars wider than 3.5 inches can be very difficult to wick, and CandleScience's multi-wick guide says multi-wick containers should be at least 3.5 inches across. Its support team says a jar 4 inches or larger may not get a full melt pool from one wick in a roughly 4-hour burn.
  • Odd shapes. Long rectangles, squares and ovals can need more than one wick even when they're narrower in one direction.
  • Some waxes. CandleScience notes some waxes need two wicks even in smaller jars, so test one and two wicks in containers above 3 inches.
  • Very wide vessels. Dough bowls and large planters can need three or more.

Not sure how wide your jar is? Common sizes are in the candle jar sizes chart. For example, the 8 oz apothecary jar there is 3.8 inches across, which puts it in two-wick territory.

How to size wicks for a double wick candle

Size by section, not by the whole jar. CandleScience's method:

Section width = jar diameter ÷ number of wicks

Jar diameterWicksSize each wick for
3.5 in8.9 cm21.75 in4.4 cm
4 in10.2 cm22 in5.1 cm
4 in10.2 cm31.33 in3.4 cm
5 in12.7 cm22.5 in6.4 cm
6 in15.2 cm32 in5.1 cm

Then look up a wick rated for that section width in your supplier's chart for your wax. Northwood notes that multi-wick candles generally use smaller wicks than a single wick in the same jar. Test two or three sizes, and make a separate tester for each fragrance. See the candle wick size guide for choosing a wick series.

Where to place two or three wicks

  • Two wicks: CandleScience suggests placing each wick about halfway between the centre and the edge. Trace the jar's base on paper, fold it in half, and mark the midpoint of each half.
  • Keep them apart: CandleScience recommends at least 1.5 inches between wicks, and its support team about an inch between each wick and the side wall.
  • Three wicks: Village Craft & Candle divides the paper template into three 120-degree sections and places a wick in each.
  • Don't push them to the edge. Northwood says a common mistake is spacing wicks too far apart. A flame close to the glass overheats the jar.
  • Hold them straight. Stick the wick tabs down firmly. Northwood suggests a two-wick bar, which holds both wicks at evenly spaced notches while the wax sets.

In a 4 inch jar, the halfway rule puts each wick 1 inch from the centre, so the wicks are 2 inches apart and 1 inch from the glass. That meets both spacing guidelines.

Burn testing a double wick candle

Two flames put out more heat than one, so test the whole burn. Northwood's checklist for a well-wicked candle:

  • Flames about 1 inch tall, burning steadily without smoke or soot.
  • The wax melts all the way to the edge.
  • Once fully melted, the melt pool is ¼ to ¾ inch deep.
  • The container stays below 175°F (79°C) for glass, or 150°F (66°C) for tins.

If the pool is too deep or the jar gets too hot, go down a wick size or use fewer wicks. CandleScience also notes that jars that narrow toward the top trap heat, so they often do best one size smaller. If wax is left on the walls, size up or add a wick. Record each test on the candle recipe sheet.

Do double wick candles burn faster?

Two flames melt wax faster than one, so a double wick candle uses up its wax sooner than the same amount of wax with one wick. In a wide jar that's the trade-off for a full melt pool: a single wick there tends to tunnel, leaving wax unburned on the sides. See candle tunneling.

Frequently asked questions

What size jar needs two wicks?

Usually jars about 3.5 to 4 inches across or wider. CandleScience suggests testing one and two wicks in any container above 3 inches, because some waxes need two wicks even in smaller jars.

How far apart should two wicks be?

CandleScience recommends at least 1.5 inches apart, placed about halfway between the centre and the edge, with about an inch between each wick and the side of the jar.

Do you use smaller wicks for a double wick candle?

Yes. Size each wick for its share of the jar: divide the diameter by the number of wicks. A 4 inch jar with two wicks takes two wicks rated for 2 inches, not two 4 inch wicks.

Why is my double wick candle getting too hot?

The wicks are probably too big or too close to the glass. Go down a size, move the wicks in toward the centre, or try one wick fewer, then test again.

Can I use wooden wicks for a double wick candle?

Yes. Village Craft & Candle uses two wood wicks in a 4 inch jar and lines up the wider side of each wick with the wider side of the jar. See the wooden wick guide for sizing and trimming.

Wide jar, more wax. The wax & fragrance calculator works out how much wax and fragrance oil a large jar needs.

Sources: 3.5 inch minimum, section sizing, halfway placement, 1.5 inch spacing, tapered jars and over-wicking from CandleScience: multi-wick candles; 4 inch diameter, odd shapes, testing above 3 inches and 1 inch from the walls from CandleScience support: should I double wick my candles?; wide jars, smaller wicks, spacing mistakes and the burn test checklist from Northwood: how to make double and triple wick candles; paper templates, three-wick placement and wood wicks from Village Craft & Candle: adding multiple wicks.